Go Back OFN Forums > Fabrication > Hotrod Fabrication

Hotrod Fabrication Hotrod Fabrication


Hotrod Fabrication Hotrod Fabrication

Reply
 
Thread Tools
  #1  
Old 03-02-2011, 10:35 AM
jackalope's Avatar
jackalope jackalope is offline
Master Fabricator
 
Join Date: Aug 2004
Location: St. Peters, MO near St. Louis
Posts: 1,433
"New" project Model A

I finally found a Model A for a rod project I have wanted to do for some time. I put a "Wanted" add on CL some time back and received a call from a storage locker where an unfinished project was sitting.
I went to check it out and what I found was a gem.
It is a 1928 Model A Sedan. It already had been in the process of being hot rodded. Came with 4" dropped axkle and 4 link with coilovers and D60 rear with disc brakes! Aftermarket frame.
I have had the entire vehicle about 2 months but was unable to start any work until last Sunday when I finally got it off the trailer.
So far I have only put the front cowel quarter panels on.
The top has already been chopped but the work all around is shotty at best. I will be chopping 1-2" while keeping the rear window the same as it currently sits.
I need to figure how I am going to Z the frame given the suspension it currently has. I imagine the rear 4 link will go in favor of air bags.
Channeling will come along hopefully soon too depending on time.
This thread will be slow growing but here is what it looks like----FOR NOW!
BTW, sorry for the $hitty pic quality!
Attached Thumbnails
Click image for larger version

Name:	IMG00076-20110302-0902.jpg
Views:	290
Size:	56.5 KB
ID:	7055   Click image for larger version

Name:	IMG00077-20110302-0902.jpg
Views:	276
Size:	56.3 KB
ID:	7056   Click image for larger version

Name:	IMG00078-20110302-0903.jpg
Views:	262
Size:	57.3 KB
ID:	7057  

Click image for larger version

Name:	IMG00079-20110302-0903.jpg
Views:	285
Size:	44.7 KB
ID:	7058  
Reply With Quote
  #2  
Old 03-02-2011, 11:32 AM
Graham08's Avatar
Graham08 Graham08 is offline
Master Fabricator
 
Join Date: May 2006
Location: Denver, NC
Posts: 1,724
Nice! I really dig Ford's Tudor sedans in about every body style (Model A, '32, '33-34, etc.).

What style are you planning to go with it? What powerplant?
Reply With Quote
  #3  
Old 03-02-2011, 11:43 AM
jackalope's Avatar
jackalope jackalope is offline
Master Fabricator
 
Join Date: Aug 2004
Location: St. Peters, MO near St. Louis
Posts: 1,433
Quote:
Originally Posted by Graham08 View Post
Nice! I really dig Ford's Tudor sedans in about every body style (Model A, '32, '33-34, etc.).

What style are you planning to go with it? What powerplant?
From a styling standpoint, I am going for the proverbial "rat rod" look but a little more than that. I am wanting it to be more "rough" however with a MATTE black slather of paint.

Power plant will be a basic SBC. I have a 400+ hp SBC in the shop but it is not mine. It has been in storage for 5+yrs! I need to just "borrow" it for ................ever! ;-)

It has a 700r4 trans in it now along with a partial SBC. Not a bad platform (all around) to start with!
Reply With Quote
  #4  
Old 03-02-2011, 12:30 PM
Chocflip201's Avatar
Chocflip201 Chocflip201 is offline
Master Fabricator
 
Join Date: Jan 2009
Location: Pleasant Grove, Utah
Posts: 930
Well what the real question is is how much did you end up paying to get this?
Reply With Quote
  #5  
Old 03-02-2011, 07:26 PM
jackalope's Avatar
jackalope jackalope is offline
Master Fabricator
 
Join Date: Aug 2004
Location: St. Peters, MO near St. Louis
Posts: 1,433
Quote:
Originally Posted by Chocflip201 View Post
Well what the real question is is how much did you end up paying to get this?
I think I did good. I landed it for $4k.

As I mentioned before, the work is pretty crappy. There is a sun roof grafted in the top that will come out but after I do the additional chop. It will provide some extra stability. I am going to try and get a bunch of bracing materials and weld them in this weekend. If I get real energetic, I may chop it. I imagine my ADD will kick in and beer will become priority.

I will update as I make progress.

Grant
Reply With Quote
  #6  
Old 03-07-2011, 12:13 PM
jackalope's Avatar
jackalope jackalope is offline
Master Fabricator
 
Join Date: Aug 2004
Location: St. Peters, MO near St. Louis
Posts: 1,433
Here are some more. I laid out the line and chopped 2" more. I left the rear window the same height. I pretty much had it laid out, reinforced, chopped, and tacked back together in under 4hrs. Not bad for working by myself.

Grant
Attached Thumbnails
Click image for larger version

Name:	IMG00082-20110304-1117.jpg
Views:	284
Size:	31.6 KB
ID:	7062   Click image for larger version

Name:	IMG00083-20110304-1117.jpg
Views:	269
Size:	53.0 KB
ID:	7063   Click image for larger version

Name:	IMG00084-20110304-1218.jpg
Views:	260
Size:	59.6 KB
ID:	7064  

Click image for larger version

Name:	IMG00085-20110304-1218.jpg
Views:	266
Size:	48.5 KB
ID:	7065   Click image for larger version

Name:	IMG00086-20110304-1218.jpg
Views:	248
Size:	53.1 KB
ID:	7066   Click image for larger version

Name:	IMG00087-20110304-1219.jpg
Views:	261
Size:	48.5 KB
ID:	7067  

Reply With Quote
  #7  
Old 03-07-2011, 12:15 PM
jackalope's Avatar
jackalope jackalope is offline
Master Fabricator
 
Join Date: Aug 2004
Location: St. Peters, MO near St. Louis
Posts: 1,433
And a few more:
Attached Thumbnails
Click image for larger version

Name:	IMG00088-20110304-1308.jpg
Views:	265
Size:	62.9 KB
ID:	7068   Click image for larger version

Name:	IMG00089-20110304-1341.jpg
Views:	245
Size:	60.1 KB
ID:	7069   Click image for larger version

Name:	IMG00090-20110304-1341.jpg
Views:	266
Size:	65.4 KB
ID:	7070  

Click image for larger version

Name:	IMG00091-20110304-1548.jpg
Views:	259
Size:	41.1 KB
ID:	7071   Click image for larger version

Name:	IMG00092-20110304-1549.jpg
Views:	265
Size:	53.9 KB
ID:	7072   Click image for larger version

Name:	IMG00093-20110306-1610.jpg
Views:	265
Size:	66.0 KB
ID:	7073  

Reply With Quote
  #8  
Old 03-07-2011, 12:16 PM
jackalope's Avatar
jackalope jackalope is offline
Master Fabricator
 
Join Date: Aug 2004
Location: St. Peters, MO near St. Louis
Posts: 1,433
And lastly, here is one from the front.

In order for me to get the stance I want, I am going to have to cut out all of the 4 link that is currently in place in the rear and kick the rear up quite a bit. I am still going to stick with the coilovers suspension in place of a standard airbag set up.

I will also be extending the frame forward the cowel roughly 3" which will give me enough firewall clearance too. Obviously the frame will be "Z'd" 4".

Once the frame is chopped up and put back together, I will channel the body accordingly and then go from there.

Grant
Attached Thumbnails
Click image for larger version

Name:	IMG00094-20110306-1610.jpg
Views:	274
Size:	69.6 KB
ID:	7074  

Last edited by jackalope; 03-07-2011 at 12:44 PM.
Reply With Quote
  #9  
Old 03-07-2011, 04:39 PM
D.G.F's Avatar
D.G.F D.G.F is offline
Fabricator
 
Join Date: Sep 2008
Location: Las Vegas,Nevada
Posts: 92
love the chop! just enough so it looks good!
Reply With Quote
  #10  
Old 03-07-2011, 04:41 PM
D.G.F's Avatar
D.G.F D.G.F is offline
Fabricator
 
Join Date: Sep 2008
Location: Las Vegas,Nevada
Posts: 92
Quote:
Originally Posted by jackalope View Post
Power plant will be a basic SBC. I have a 400+ hp SBC in the shop but it is not mine. It has been in storage for 5+yrs! I need to just "borrow" it for ................ever! ;-)
!
i would say after five years its yours (storage fees )
Reply With Quote
  #11  
Old 03-07-2011, 05:56 PM
TheBandit's Avatar
TheBandit TheBandit is offline
Instagram @chevyhotrodder
 
Join Date: Jan 2006
Location: Ventura County CA
Posts: 4,330
You hit it out of the ballpark with that chop. Just the right amount - it's going to be wicked!
__________________
Clint

Don't limit your challenges. Challenge your limits.
Reply With Quote
  #12  
Old 03-07-2011, 06:18 PM
jackalope's Avatar
jackalope jackalope is offline
Master Fabricator
 
Join Date: Aug 2004
Location: St. Peters, MO near St. Louis
Posts: 1,433
I was not sure how much to chop at first but after I measured the mack window and realized I wanted that to remain the same height, it became clear that the 2" would be a good amount for me.

I wish I had an extra set of hands at times, but then I would have to listen to them talk the rest of the time.

I am kinda bummed that I need to cut the suspension, etc up/off. Partially because it is a $hitty job and also because it interferes with the frame configuration I am going with. I guess, though, that that is a plus. If it were a smoking job and excellent work, I would really have a hard time chopping it up.

I must say, this is a welcome relief from working on Jeeps, etc. This is just something I have wanted to screw around with for a long time and finally got the chance.

Not something that will get done overnight, but something I should stay relatively focussed on.
Reply With Quote
  #13  
Old 05-30-2011, 05:29 PM
PedalTek's Avatar
PedalTek PedalTek is offline
Fabricator
 
Join Date: Nov 2009
Location: Phoenix, AZ
Posts: 35
Looks awesome so far man. I just recently took on a side project finishing up a 30 Ford model A truck hot rod. FYI: on OFN, you may be able to get away with the term "rat rod". But trust me, be very very careful where else you use that term. I posted some questions on popular "traditional hot rod forum" using the term rat rod... And holy crap I got eaten alive. Rat rods, by traditional hot rod terms, are pos's built by hipster kids looking to piss anyone and everyone off and usually include flame throwers, lots of skulls, mini truck lowrider engineering and shoddy workmanship at best. It really is all about the wording. If you call it a hot rod, you get respect. If you call the same car/truck a rat rod.... Brace yourself! Haha! Those "traditional" guys are not messing around!!

I look forward to seeing this come together for ya. BTW, the one I'm working on has a custom frame, Z'd in the rear, 4 linked, on air bags with a cantilever linkage set up. Pretty slick. Check the pics.



[IMG][/IMG]

[IMG][/IMG]
Reply With Quote
  #14  
Old 05-30-2011, 05:52 PM
DJPyro's Avatar
DJPyro DJPyro is offline
Master Fabricator
 
Join Date: Jul 2009
Posts: 104
^ Now THAT is cool...

Awesome find man, and I agree, the chop is just right. I really look forward to seeing the progress on this.
Reply With Quote
  #15  
Old 05-30-2011, 06:41 PM
AngryBee's Avatar
AngryBee AngryBee is offline
Fabricator
 
Join Date: Nov 2010
Location: Southern Queensland, Australia
Posts: 53
Looks the goods. Not sure about the plastic fans on the back though, kind of detracts from the look IMO. If they were metal with rusted cages it would look much better.

And as for the "Rat Rod" issue, you know what they say about old people and change haha. But yeah, I know which "popular" forum you are talking about and yes they are very touchy about it.
Reply With Quote
  #16  
Old 05-30-2011, 06:44 PM
METAL TWISTER's Avatar
METAL TWISTER METAL TWISTER is offline
Master Fabricator
 
Join Date: Feb 2007
Location: SoCal. Diego
Posts: 719
Looks good... did someone cut a sun roof into that thing?
Reply With Quote
  #17  
Old 05-30-2011, 09:17 PM
jackalope's Avatar
jackalope jackalope is offline
Master Fabricator
 
Join Date: Aug 2004
Location: St. Peters, MO near St. Louis
Posts: 1,433
I like that truck. I was actually looking for one when I ran across mine.

As for the question about some cutting a sunroof, yes. Someone took an entire roof out of a minivan I think and slapped it in the roof. They did a real crappy job too.

I have the body and frame seperated and am getting ready to chop the frame. It is a nice Pete and Jakes frame and suspension. It has the highboy style with triangulated 4 link rear. I am going to keep the suspension the way it is and still cut the frame. I think I can make it do what I want with totally losing the suspension geometry, etc.

Oh, and I will be cutting the hideous roof out too! ;-)

Grant
Reply With Quote
  #18  
Old 05-30-2011, 10:44 PM
PedalTek's Avatar
PedalTek PedalTek is offline
Fabricator
 
Join Date: Nov 2009
Location: Phoenix, AZ
Posts: 35
http://m802.photobucket.com/albums/PedalTek/hot%20rod/?

Or: http://s802.photobucket.com/albums/PedalTek/hot%20rod/?

I threw up a few detailed (as possible) pics of the 4-link just in case you wanted some ideas..?
Reply With Quote
  #19  
Old 08-15-2011, 08:11 PM
jackalope's Avatar
jackalope jackalope is offline
Master Fabricator
 
Join Date: Aug 2004
Location: St. Peters, MO near St. Louis
Posts: 1,433
I finally got a chance to get back into the shop to play around with this project. The heat has just been too brutal to do too much. With the break in the heat, I got a chance to chop the frame up and extend it. Dropped the middle section 4 inches and then extended the front 5 inches. I reinforced the frame. After that was complete, the temperature was so nice that I had to keep going. I channeled the body by cutting the floor boards out. As you can see in the final front shot, it is not fully dropped as much as it will be. Reason being, I had welded a reinforcement in the way of part of the frame. If I don't go outta town next week, I will take care of that and start putting the floor in it.

In the last pic, you can see that it is a bit lower than the other pics. It still has about 3-4" more to drop down. It's getting there and should be full steam ahead if the weather hods out!
Attached Thumbnails
Click image for larger version

Name:	IMG00242-20110814-1352.jpg
Views:	698
Size:	57.7 KB
ID:	7189   Click image for larger version

Name:	IMG00243-20110814-1403.jpg
Views:	254
Size:	58.8 KB
ID:	7190   Click image for larger version

Name:	IMG00244-20110814-1633.jpg
Views:	258
Size:	63.2 KB
ID:	7191  

Click image for larger version

Name:	IMG00245-20110814-1633.jpg
Views:	227
Size:	61.9 KB
ID:	7192   Click image for larger version

Name:	IMG00246-20110814-1648.jpg
Views:	247
Size:	55.6 KB
ID:	7193  

Last edited by jackalope; 08-15-2011 at 08:14 PM.
Reply With Quote
  #20  
Old 08-22-2011, 02:04 PM
jackalope's Avatar
jackalope jackalope is offline
Master Fabricator
 
Join Date: Aug 2004
Location: St. Peters, MO near St. Louis
Posts: 1,433
Got a chance to get back up to the shop this past Saturday. I did not get into the floor boards yet, but that will be next weekend. Here are the latest pics. Nothing too spectacular, but this is the look. I will have slightly larger tires in the rear which will give a slight rake to the overall look. Not much but just enough IMO.
Attached Thumbnails
Click image for larger version

Name:	IMG00254-20110820-1530.jpg
Views:	240
Size:	49.5 KB
ID:	7196   Click image for larger version

Name:	IMG00255-20110820-1531.jpg
Views:	240
Size:	48.2 KB
ID:	7197   Click image for larger version

Name:	IMG00256-20110820-1531.jpg
Views:	250
Size:	44.9 KB
ID:	7198  

Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 08:28 PM.

Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Template-Modifications by TMS
Copyright 2012, Offroad Fabrication Network