Go Back OFN Forums > Fabrication > General Fabrication

General Fabrication Any Fab that does not fit into another Forum


General Fabrication Any Fab that does not fit into another Forum

Reply
 
Thread Tools
  #21  
Old 09-03-2016, 07:13 PM
70k5kid's Avatar
70k5kid 70k5kid is offline
Junior Fabricator
 
Join Date: Aug 2016
Location: North Central WA
Posts: 1
COOL RIG! Maybe think about replacing the front wig/wags with some 8" PIA's (or yer favorite flavor illuminators)
Reply With Quote
  #22  
Old 11-28-2016, 11:14 AM
$CEEP's Avatar
$CEEP $CEEP is offline
Moderator
 
Join Date: Feb 2005
Location: albumexinewquerqueco
Posts: 998
KOH prep. Need a fridge and stove.

Had to cut a big ol hole in the side for the LP fridge ventilation.


got that all installed, had to remove the lower window for upper ventilation (not installed yet)


free fridge, cooktop and countertop. Dunno if I'll put a drawer under the stove, or just box it out for a small storage compartment. still need to add a backsplash and caulk everything.



Next on the list install furnace, run lp lines, mount tanks. Then get sink finished, add fresh and greywater tanks and heat exchanger.
Reply With Quote
  #23  
Old 11-28-2016, 12:45 PM
TheBandit's Avatar
TheBandit TheBandit is offline
Instagram @chevyhotrodder
 
Join Date: Jan 2006
Location: Southern California
Posts: 4,174
You're well on your way to full service RV glamping!
__________________
Clint
Reply With Quote
  #24  
Old 12-05-2016, 04:06 PM
$CEEP's Avatar
$CEEP $CEEP is offline
Moderator
 
Join Date: Feb 2005
Location: albumexinewquerqueco
Posts: 998
Got the doghouse built for the furnace.


Fitted the backsplash then dad went nuts and trimmed it all out!


Reply With Quote
  #25  
Old 12-12-2016, 10:09 AM
$CEEP's Avatar
$CEEP $CEEP is offline
Moderator
 
Join Date: Feb 2005
Location: albumexinewquerqueco
Posts: 998
Couldn't find an acceptable (to me) solution to mounting the LP tanks so I picked up a couple forklift straps and we hacked into them sat. Had to add some structure to mount them, as well as support the bottle and make them lockable.



dunno why the left tank looks like its sitting all funky compared to the right one. Its all square and true. Will have to look into that as its buggin the shit outtah me.


Then moved on to some bed rails to keep our sober butts from falling outtah the dang bunk.

Reply With Quote
  #26  
Old 12-19-2016, 10:27 AM
$CEEP's Avatar
$CEEP $CEEP is offline
Moderator
 
Join Date: Feb 2005
Location: albumexinewquerqueco
Posts: 998
Was little chilly this weekend but got a lot done.
Stove is cooking and fridge is cooling! Laid in all the gas lines. Everything but the furnace is up and running. Need a new thermostat and to tap some power for it somewhere.


Last edited by $CEEP; 12-19-2016 at 02:03 PM.
Reply With Quote
  #27  
Old 01-09-2017, 10:10 AM
$CEEP's Avatar
$CEEP $CEEP is offline
Moderator
 
Join Date: Feb 2005
Location: albumexinewquerqueco
Posts: 998
Busy week.
Got the heat exchanger mounted, fresh and grey water tanks installed, thermostat and furnace are up and running, and built a fuel/oil/coolant/firewood holder out back.





Reply With Quote
  #28  
Old 01-12-2017, 07:39 PM
TheBandit's Avatar
TheBandit TheBandit is offline
Instagram @chevyhotrodder
 
Join Date: Jan 2006
Location: Southern California
Posts: 4,174
Looks like you put the dimple dies to work! Nice addition. What is the heat exchanger used for?
__________________
Clint
Reply With Quote
  #29  
Old 01-16-2017, 10:32 AM
$CEEP's Avatar
$CEEP $CEEP is offline
Moderator
 
Join Date: Feb 2005
Location: albumexinewquerqueco
Posts: 998
Quote:
Originally Posted by TheBandit View Post
Looks like you put the dimple dies to work! Nice addition. What is the heat exchanger used for?
Had those dies for like 3 years and have never used em! Finally had a good project for them!

Heat exchanger for hot water.

Getting close to done now. Need to tie into the coolant system and then hot water will be complete. Need to add a fill line to the freshwater tank and wire the pump and we'll have water to the sink and shower! Greywater system is complete.



Reply With Quote
  #30  
Old 01-16-2017, 11:34 AM
CarterKraft's Avatar
CarterKraft CarterKraft is offline
Master Fabricator
 
Join Date: Oct 2009
Location: DFW
Posts: 816
Looking good. So did you build the heat exchanger? Cool idea.
Reply With Quote
  #31  
Old 01-16-2017, 11:45 AM
$CEEP's Avatar
$CEEP $CEEP is offline
Moderator
 
Join Date: Feb 2005
Location: albumexinewquerqueco
Posts: 998
Quote:
Originally Posted by CarterKraft View Post
Looking good. So did you build the heat exchanger? Cool idea.
I didn't

Buddy of mine was in the mobile steam cleaning industry for quite a few years. This was an exchanger he designed for his employer. The freshwater is pumped through a coil of finned copper tubing. Hot engine coolant is pumped through/fills the entire "waterpig" .

He's confident it will work great for what we are doing.
Reply With Quote
  #32  
Old 01-16-2017, 11:56 AM
CarterKraft's Avatar
CarterKraft CarterKraft is offline
Master Fabricator
 
Join Date: Oct 2009
Location: DFW
Posts: 816
Cool, sounds like awesome idea. You could even add a bung and a element for electrical heating.
Reply With Quote
Reply

Bookmarks


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:46 AM.

Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Template-Modifications by TMS
Copyright 2012, Offroad Fabrication Network